What is the precise meaning of "ours" and "theirs" in git?

I suspect you're confused here because it's fundamentally confusing. To make things worse, the whole ours/theirs stuff switches roles (becomes backwards) when you are doing a rebase.

Ultimately, during a git merge, the "ours" branch refers to the branch you're merging into:

git checkout merge-into-ours

and the "theirs" branch refers to the (single) branch you're merging:

git merge from-theirs

and here "ours" and "theirs" makes some sense, as even though "theirs" is probably yours anyway, "theirs" is not the one you were on when you ran git merge.

While using the actual branch name might be pretty cool, it falls apart in more complex cases. For instance, instead of the above, you might do:

git checkout ours
git merge 1234567

where you're merging by raw commit-ID. Worse, you can even do this:

git checkout 7777777    # detach HEAD
git merge 1234567       # do a test merge

in which case there are no branch names involved!

I think it's little help here, but in fact, in gitrevisions syntax, you can refer to an individual path in the index by number, during a conflicted merge

git show :1:README
git show :2:README
git show :3:README

Stage #1 is the common ancestor of the files, stage #2 is the target-branch version, and stage #3 is the version you are merging from.


The reason the "ours" and "theirs" notions get swapped around during rebase is that rebase works by doing a series of cherry-picks, into an anonymous branch (detached HEAD mode). The target branch is the anonymous branch, and the merge-from branch is your original (pre-rebase) branch: so "--ours" means the anonymous one rebase is building while "--theirs" means "our branch being rebased".


As for the gitattributes entry: it could have an effect: "ours" really means "use stage #2" internally. But as you note, it's not actually in place at the time, so it should not have an effect here ... well, not unless you copy it into the work tree before you start.

Also, by the way, this applies to all uses of ours and theirs, but some are on a whole file level (-s ours for a merge strategy; git checkout --ours during a merge conflict) and some are on a piece-by-piece basis (-X ours or -X theirs during a -s recursive merge). Which probably does not help with any of the confusion.

I've never come up with a better name for these, though. And: see VonC's answer to another question, where git mergetool introduces yet more names for these, calling them "local" and "remote"!


The 'ours' in Git is referring to the original working branch which has authoritative/canonical part of git history.

The 'theirs' refers to the version that holds the work in order to be rebased (changes to be replayed onto the current branch).

This may appear to be swapped to people who are not aware that doing rebasing (e.g. git rebase) is actually taking your work on hold (which is theirs) in order to replay onto the canonical/main history which is ours, because we're rebasing our changes as third-party work.

The documentation for git-checkout was further clarified in Git >=2.5.1 as per f303016 commit:

--ours --theirs

When checking out paths from the index, check out stage #2 ('ours') or #3 ('theirs') for unmerged paths.

Note that during git rebase and git pull --rebase, 'ours' and 'theirs' may appear swapped; --ours gives the version from the branch the changes are rebased onto, while --theirs gives the version from the branch that holds your work that is being rebased.

This is because rebase is used in a workflow that treats the history at the remote as the shared canonical one, and treats the work done on the branch you are rebasing as the third-party work to be integrated, and you are temporarily assuming the role of the keeper of the canonical history during the rebase. As the keeper of the canonical history, you need to view the history from the remote as ours (i.e. "our shared canonical history"), while what you did on your side branch as theirs (i.e. "one contributor's work on top of it").

For git-merge it's explain in the following way:

ours

This option forces conflicting hunks to be auto-resolved cleanly by favoring our version. Changes from the other tree that do not conflict with our side are reflected to the merge result. For a binary file, the entire contents are taken from our side.

This should not be confused with the ours merge strategy, which does not even look at what the other tree contains at all. It discards everything the other tree did, declaring our history contains all that happened in it.

theirs

This is the opposite of ours.

Further more, here is explained how to use them:

The merge mechanism (git merge and git pull commands) allows the backend merge strategies to be chosen with -s option. Some strategies can also take their own options, which can be passed by giving -X<option> arguments to git merge and/or git pull.


So sometimes it can be confusing, for example:

  • git pull origin master where -Xours is our local, -Xtheirs is theirs (remote) branch
  • git pull origin master -r where -Xours is theirs (remote), -Xtheirs is ours

So the 2nd example is opposite to the 1st one, because we're rebasing our branch on top of the remote one, so our starting point is remote one, and our changes are treated as external.

Similar for git merge strategies (-X ours and -X theirs).


I know this has been answered, but this issue confused me so many times I've put up a small reference website to help me remember: https://nitaym.github.io/ourstheirs/

Here are the basics:

Merges:

$ git checkout master 
$ git merge feature

If you want to select the version in master:

$ git checkout --ours codefile.js

If you want to select the version in feature:

$ git checkout --theirs codefile.js

Rebases:

$ git checkout feature 
$ git rebase master 

If you want to select the version in master:

$ git checkout --ours codefile.js

If you want to select the version in feature:

$ git checkout --theirs codefile.js

(This is for complete files, of course)

Tags:

Git

Merge