Do conditional statements slow down shaders?

It's highly dependent on the hardware and on the condition.

If your condition is a uniform : don't bother, let the compiler deal with it. If your condition is something dynamic (like a value computed from attribute or fetched from texture or something), then it's more complicated.

For that latter case you'll pretty much have to test and benchmark because it'll depend on the complexity of the code in each branches and how 'consistent' the branch decision is.

For instance if one of the branch is taken 99% of the case and discards the fragment, then most likely you want to keep the conditional. But OTOH in your simple example above if enable is some dynamic condition, the arithmetic select might be better.

Unless you have a clear cut case like the above, or unless you're optimizing for one fixed known architecture, you're probably better off the compiler figure that out for you.


What is it about shaders that even potentially makes if statements performance problems? It has to do with how shaders get executed and where GPUs get their massive computing performance from.

Separate shader invocations are usually executed in parallel, executing the same instructions at the same time. They're simply executing them on different sets of input values; they share uniforms, but they have different internal registers. One term for a group of shaders all executing the same sequence of operations is "wavefront".

The potential problem with any form of conditional branching is that it can screw all that up. It causes different invocations within the wavefront to have to execute different sequences of code. That is a very expensive process, whereby a new wavefront has to be created, data copied over to it, etc.

Unless... it doesn't.

For example, if the condition is one that is taken by every invocation in the wavefront, then no runtime divergence is needed. As such, the cost of the if is just the cost of checking a condition.

So, let's say you have a conditional branch, and let's assume that all of the invocations in the wavefront will take the same branch. There are three possibilities for the nature of the expression in that condition:

  • Compile-time static. The conditional expression is entirely based off of compile-time constants. As such, you know from looking at the code which branches will be taken. Pretty much any compiler handles this as part of basic optimization.
  • Statically uniform branching. The condition is based off of expressions involving things which are known at compile-time to be constant (specifically, constants and uniform values). But the value of the expression will not be known at compile-time. So the compiler can statically be certain that wavefronts will never be broken by this if, but the compiler cannot know which branch will be taken.
  • Dynamic branching. The conditional expression contains terms other than constants and uniforms. Here, a compiler cannot tell a priori if a wavefront will be broken up or not. Whether that will need to happen depends on the runtime evaluation of the condition expression.

Different hardware can handle different branching types without divergence.

Also, even if a condition is taken by different wavefronts, the compiler could restructure the code to not require actual branching. You gave a fine example: output = input*enable + input2*(1-enable); is functionally equivalent to the if statement. A compiler could detect that an if is being used to set a variable, and thus execute both sides. This is frequently done for cases of dynamic conditions where the bodies of the branches are small.

Pretty much all hardware can handle var = bool ? val1 : val2 without having to diverge. This was possible way back in 2002.

Since this is very hardware-dependent, it... depends on the hardware. There are however certain epochs of hardware that can be looked at:

Desktop, Pre-D3D10

There, it's kinda the wild west. NVIDIA's compiler for such hardware was notorious for detecting such conditions and actually recompiling your shader whenever you changed uniforms that affected such conditions.

In general, this era is where about 80% of the "never use if statements" comes from. But even here, it's not necessarily true.

You can expect optimization of static branching. You can hope that statically uniform branching won't cause any additional slowdown (though the fact that NVIDIA thought recompilation would be faster than executing it makes it unlikely at least for their hardware). But dynamic branching is going to cost you something, even if all of the invocations take the same branch.

Compilers of this era do their best to optimize shaders so that simple conditions can be executed simply. For example, your output = input*enable + input2*(1-enable); is something that a decent compiler could generate from your equivalent if statement.

Desktop, Post-D3D10

Hardware of this era is generally capable of handling statically uniform branches statements with little slowdown. For dynamic branching, you may or may not encounter slowdown.

Desktop, D3D11+

Hardware of this era is pretty much guaranteed to be able to handle dynamically uniform conditions with little performance issues. Indeed, it doesn't even have to be dynamically uniform; so long as all of the invocations within the same wavefront take the same path, you won't see any significant performance loss.

Note that some hardware from the previous epoch probably could do this as well. But this is the one where it's almost certain to be true.

Mobile, ES 2.0

Welcome back to the wild west. Though unlike Pre-D3D10 desktop, this is mainly due to the huge variance of ES 2.0-caliber hardware. There's such a huge amount of stuff that can handle ES 2.0, and they all work very differently from each other.

Static branching will likely be optimized. But whether you get good performance from statically uniform branching is very hardware-dependent.

Mobile, ES 3.0+

Hardware here is rather more mature and capable than ES 2.0. As such, you can expect statically uniform branches to execute reasonably well. And some hardware can probably handle dynamic branches the way modern desktop hardware does.